Saturday, 25 July 2020

How to Tie a Dimple

A tie dimple refers to the small indent in the center of a tie near the top of the knot. It adds another dimension to your outfit by giving your tie a little personality and class. A dimple can be applied to any type of necktie knot, although they tend to naturally occur with Eldridge, Capsule, and Nicky knots. To add your dimple, tie your tie the way you normally would, and stop right before you get to the part where you tighten the knot. Then, you can choose to add your dimple from the top or bottom of the knot.

[Edit]Steps

[Edit]Tying Your Tie

  1. Choose your necktie and set the length before making the knot. Select the necktie you think that goes best with your outfit. Line the blade and tail up over your shoulders to set the length. Then, begin to assemble the knot. A dimple is easily added to any kind of knot, so it doesn’t matter which particular knot you choose.[1]
    Tie a Dimple Step 1.jpg
    • The blade refers to the larger piece of fabric that hangs in front. The tail is the skinnier piece of the tie that sits behind the blade.
  2. Stop tying the tie at the point where you’re about to secure the knot. When you get to the part where you pull the blade down all the way through the knot to tighten the tie, stop. Slide the blade 3/4 of the way through the knot and gently let the tie hang. Leave at least of space between the portion of the blade looped over the knot and the top of the knot itself.[2]
    Tie a Dimple Step 2.jpg
    • Maintain enough slack in the blade and knot to reach in between the space where the front portion of the knot covers the blade.
  3. Line your tie up and check the length before adding the dimple. Make sure that the knot is assembled perfectly and that the blade is at the perfect length before proceeding. The bottom of the blade should rest over your belt buckle, so if there is of space remaining between the top of the blade and the knot, your blade should be hanging roughly above the belt buckle.[3]
    Tie a Dimple Step 3.jpg
    • You cannot add a dimple after tightening your necktie, and the dimple won’t look nearly as good if you loosen the knot after adding it to adjust the length of your tie.
    • If you need to reassemble the knot or adjust the length, repeat these steps to create a new knot.

[Edit]Folding the Dimple from Above

  1. Slide your thumbs under the loop on top of the knot. Insert your thumbs underneath the portion of the blade that is loosely sticking out the top of the knot. Orient your palms to face up so that you’re holding the loop with the pads of your thumbs. Keep your hands as symmetrical as possible for an even dimple.[4]
    Tie a Dimple Step 4.jpg
    • Folding the dimple from above is a little easier than adding it from below, but you have less control over the size of the dimple.
  2. Pinch the fabric inwards using both index fingers. Slide your index fingers over your thumbs and pinch them inwards to add a seam to the loop. Transfer your grip on the loop to your nondominant hand and hold the loop in place.[5]
    Tie a Dimple Step 5.jpg
    • You don’t need to squeeze hard to hold the dimple in place.
  3. Slide the blade down through the knot. Grab the blade just underneath the knot with your dominant hand. Maintain the dimple with your nondominant hand. Slowly pull the blade down to tighten your knot.[6]
    Tie a Dimple Step 6.jpg
  4. Secure the dimple by sliding it through the back of the knot. While you’re pulling the blade down to tighten it, maintain the dimple with your nondominant hand. Slide the dimple through the front of the knot. The dimple will slide behind the front of the knot and emerge underneath it. Pull the blade all the way through to tighten your tie and secure the dimple.[7]
    Tie a Dimple Step 7.jpg
    • The dimple should sit in the middle of your tie. If it isn’t, you may be able to adjust the tie by pulling the indentation in the dimple to the left or the right.

[Edit]Adding the Dimple from Below

  1. Pinch the center of the blade just below the knot with your index finger. Grab the edges of your blade just beneath the loose knot. Use your index finger to apply pressure to the center of the fabric and add your dimple. Hold the fabric in place with your thumb and middle finger while maintaining the dimple with the index finger on the same hand.[8]
    Tie a Dimple Step 8.jpg
    • Some people use their nondominant hand to do this while other people prefer their dominant hand. Do whatever feels most comfortable to you.
    • Adding the dimple from below requires a little more dexterity, but you have more control over the location and the size of the dimple.
  2. Grip the sides of the knot gently with your other hand. Use your free hand to grab the edges of the knot by the bottom edge of the fabric. Do not squeeze or pull on the knot—the goal here is to simply stabilize it while you tighten your tie.[9]
    Tie a Dimple Step 9.jpg
    • Most people naturally squeeze the knot a little when they normally their tie. Resist the urge to do this, since the dimple will be harder to hold in place if you don’t leave yourself some room inside of the knot.
  3. Pull the blade down . Begin pulling the blade down to tighten your tie using whatever hand you’re holding the dimple with. After pulling the tie down , slide your index finger up towards the knot to move the dimple upwards.[10]
    Tie a Dimple Step 10.jpg
  4. Tighten your tie slowly while sliding the dimple up the blade. Use your other hand to brace the knot and keep the shape of your tie. Continue pulling the blade down and sliding the dimple up until your tie is tight.[11]
    Tie a Dimple Step 11.jpg
    • If the angle of the dimple looks a little off, gently tug the fabric under your knot to adjust the shape of your dimple.

[Edit]Tips

  • Whether you add your dimple above or below the knot is really a matter of personal preference. Try it both ways to figure out what feels right to you.

[Edit]References


No comments:

Post a Comment